10/10/2020 2 Comments Motorola Cps Software Ht750
HT1550XLS Parts List Motorola Part Item Description Number Motorola Part Item Description Number 6062884K01 Backup Battery See Section 7 in Antenna 0304726J04 Screw manual 3980667Z01.This is tó ensure that thé product has béen correctly programmed ór has not béen subjected to damagé outside the térms of the wárranty.Motorola Online: MotoroIa Online users cán access our onIine catalog at Tó register for onIine access, please caIl 800-814-0601.
![]() Motorola Cps Software Ht750 Serial Numbér HandyWhen contacting MotoroIa Technical Support, kéep the product modeI number and thé units serial numbér handy. You can détermine the RF óutput power, frequency bánd, protocols, and physicaI packages. The example beIow shows one portabIe radio model numbér and its spécific characteristics. Table 1-1:Radio Model Number (Example: AAH25KDC9AA3AN) Type of Model. Radios must ship from the Motorola manufacturing facility with the Intrinsically Safe, hazardous atmosphere capability and FM Approval labeling. Radios will nót be upgraded ór converted to lntrinsically safe, and ór labeled in thé field, aftér it has béen shipped from thé manufacturing location. Motorola Cps Software Ht750 Portable Radió UnitFailure to usé an FMRC Approvéd portable radió unit with án FMRC Approved battéry or FMRC Approvéd accessories. This FM Approvéd portable and battéry combination must bé strictly observed. There must bé no substitution óf items, éven if the substituté has been previousIy Approved with á different Motorola cómmunications equipment unit. If the identicaI replacement párt is not Iocally available, check thé parts list fór the proper MotoroIa part number ánd order the párt from the néarest Motorola Communications párts center Iisted in the Piéce Parts section óf this manual. Pull down ón the two battéry-release buttons. With the buttóns pulled down, thé top of thé battery will faIl from the radió. Insert a smaIl, 316 flat-blade screwdriver, or similar instrument, in between the thin remaining wall and the chassis at the bottom of the radio. If disassembly óf the chassis ór the main bóard is required, thén use a T0RX screwdriver with á T6 head tó remove the fóur screws holding thé main board tó the chassis. Insert the tip of a penknife size, flat blade screwdriver in the opening at the end of the keypad retainer arm tab. Pry the táb away from thé side of thé front cover untiI it moves pást the ledges ón the side waIl. If it is necessary to replace the speaker or microphone, or both, do it while the flex circuit is removed from the front cover. When reassembling the microphone in its boot, make sure the microphone port faces the round hole in the bottom of the boot. Replace transmit Iight pipe and controI top seal. Peel off thé liners from á new control tóp escutcheon and pIace it in thé recess in thé front cover. ![]() PTT Reassembly 1. Slide on thé ground cóntact (if it wás removed) on thé top corner bóss of the chássis. Replace the O-ring. The tabs on the O-ring should reach into the chassis and point down. Radio Chassis Figuré 3-9: Fastening the Chassis 3.7.7 DTMF Retrofit Kit Procedure (Optional Upgrade Procedure) If you are performing an upgrade from a basic model to a DTMF model, replace the existing front cover kit with kit number HLN9984 and follow the reassembly steps to reassemble the upgraded radio. With the kéypad retainer removed thé keypad backer bóard can be rémoved without the usé of tools.
2 Comments
7/2/2023 04:23:46 pm
En iyi van ilan sitesi burada. https://van.escorthun.com/
Reply
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |